Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterECO Window Systems Door Installation: The Stuart Owner’s Guide
We install ECO Window Systems doors throughout Stuart, FL, with most replacement installations running between $850 and $2,400 depending on the door style, frame condition, and whether it’s a slab swap or a full tear-out. We stock ECO-compatible hardware, rollers, hinges, and weatherstripping on our trucks, so most jobs are done in a single visit. The typical call starts the same way: a door that’s been dragging for months finally stops latching, or a homeowner notices the frame pulling away from the wall on the hinge side and realizes the original install wasn’t set right in the first place.
If that sounds familiar, we can help. TruePane Windows & Doors is an independent installer and repair shop serving Stuart and the Treasure Coast, not a division of ECO Window Systems. That means we’ll give you a straight answer on whether the door needs a part, an adjustment, or a full replacement, and we’ll do it without steering you toward a bid you don’t need.
Which ECO Window Systems Models This Applies To
ECO Window Systems manufactures a range of impact-rated and non-impact doors for the Florida market, including hinged entry doors, French doors, and sliding glass doors. The most common lines we service in Stuart are the ECO 3000 and ECO 7000 series. The 7000 series doors run heavier: thicker extruded aluminum frames, larger roller assemblies, and a deeper threshold. The 3000 series uses a lighter frame profile and smaller rollers. The rollers are not interchangeable between the two lines, and we’ve seen more than one homeowner order a set of replacement rollers online only to find they’re 4mm too wide for the track.
Here’s how to identify what you have: open the door and look at the edge of the door panel or the top rail. ECO stamps the model number on a small aluminum tag, usually near the handle or on the top corner of the frame. If the tag is missing, measure the door panel thickness. The 7000 series panels run about 1 3/4 inches thick; the 3000 series runs closer to 1 1/2. When we quote a job, we always measure twice and check the tag before ordering. For most ECO hardware, we recommend OEM parts. The aftermarket rollers and hinges for these doors are hit or miss: some hold up fine, but the steel in the cheaper ones rusts faster in the salt air we get off the St. Lucie River, and a failed roller on an impact-rated door can pull the panel out of square.
We also keep parts coverage in mind for homeowners whose ECO door was installed alongside other lines. If you have a mix of brands in the house, we can match ECO door hardware to what’s already there, and we order from the same distributors we use for Andersen, and Pella work.
Signs Your ECO Window Systems Door Installation Is Failing
- The door drags or scrapes the threshold. This usually means the rollers have worn flat or the panel has settled out of adjustment. In Stuart, the heat and humidity expand aluminum frames just enough that a door set too tight in July will bind by August. If you have to lift the door to close it, the rollers are done.
- The door won’t latch without a shove. A striker plate that no longer lines up with the latch is often the first real sign the door panel has dropped. This points to worn hinges on a hinged door or failed rollers on a slider. It’s not a lock problem; the panel is sitting lower than it did when it was installed.
- Water stains or soft drywall near the bottom corners. When an ECO door was flashed incorrectly or the threshold seal has compressed, water works its way under the sill and into the wall. We see this most often on doors installed by production crews who rushed the pan flashing. By the time the stain shows, the seal has been failing for a while.
- The door panel feels loose or rattles when it closes. That’s play in the rollers or hinge pins. An ECO door set correctly closes with a solid, even weight. If it rattles, something is loose, and loose hardware wears everything else faster.
- The frame is pulling away from the wall on the hinge side. This is the one that means the original install was wrong: undersized anchors, no shims behind the hinges, or rough opening that was never corrected. The door is essentially hanging off the wall instead of sitting in it. This needs a full reset, not a hardware swap.
Replacement Cost & What’s Included
In Stuart, a straightforward ECO door installation job, like pulling an old slab and setting a new one in an existing square frame, typically runs $850 to $1,400. A full tear-out with new frame, threshold, and interior trim runs $1,800 to $2,400, more if we’re pulling permits and replacing rotted subfloor or wall framing around the opening. Those are honest ranges, not teaser prices. The floor and the ceiling on the job are set by what’s behind the wall once we open it up.
Our quotes are written line by line on paper before we start: parts, labor, disposal, and any flashing or sealant work. No surprise line items on the bill and no change orders halfway through. Every ECO door installation we do is covered by the Done Right Promise, and we register both layers of the manufacturer warranty in writing before the truck leaves your driveway. That’s what we mean by The Keystone Standard. If the door isn’t true, the job isn’t done, and we don’t leave until it is.
Written by Dale Kessler, Owner, TruePane Windows & Doors, serving Stuart since 2008 and the Treasure Coast since 2008.
DIY or Call Us?
You can check a few things yourself before you call: whether the tag is legible, whether the frame is pulling away anywhere, and whether the panel is dragging. That information helps us quote over the phone. What I’d caution against is trying to rehang an ECO door yourself. These doors carry real weight, especially the 7000 series impact doors. Getting one out of square while it’s on the hinges can bend a panel edge or crack the glass. On top of that, the anchors and shims ECO frames need to sit square in a Florida wall opening are not intuitive. If you’ve never set a door in a rough opening before, the opening is where most of the mistakes happen. If the opening is right, the rest is just doing the work. We’d rather be the ones doing it.
Call (754) 324-4646 and we’ll talk through what you’re seeing. If it’s a quick adjustment, we’ll say so. If it needs a full install, we’ll tell you exactly what that costs before we set foot in the house.
FAQs
An ECO door installed square with proper flashing and hardware should last 15 to 25 years in Stuart, with rollers and weatherstripping replaced every 5 to 8 years. The salt air near the river accelerates wear on exposed hardware, and doors facing the lagoon tend to need roller replacement sooner than inland doors. We register both warranty layers in writing so you always know what each layer covers and for how long. Call (754) 324-4646 if your door is under 15 years and failing; we’ll tell you if a repair is worth it.
Yes, in most cases. Rollers, hinges, handles, and weatherstripping are all replaceable parts on ECO doors, and we stock the common ones on the truck. If the frame is out of square or the panel is warped, replacement makes more sense. We won’t tell you to replace a door that just needs a roller.
Most ECO door installations we do in Stuart are completed in a single day, usually four to eight hours depending on whether we’re swapping a slab or resetting a full frame. We’ll give you a time window before we start and stick to it.
We stock ECO-compatible rollers, hinges, handles, and weatherstripping for the 3000 and 7000 series on our trucks, and we can order OEM ECO parts for less common items. We’ll check the tag on your door before we order so we don’t guess.
Talk to us about your ECO door. Call (754) 324-4646 for a free estimate on ECO Window Systems door installation in Stuart. We’re at the other end of the line, day or night, and we’ll tell you what we’d do if it were our house.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Stuart and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.