Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterES Windows Custom & Geometric Windows in Stuart: What to Know First
We provide independent ES Windows custom and geometric window service in Stuart, from arched and radius units to oversized trapezoids and angled openings. Most jobs are diagnosed on the first visit and completed within one to two weeks when custom glass or hardware has to be ordered. Pricing runs higher than stock window repair because these units are measured and fabricated to spec, but we quote everything upfront on paper, register both warranty layers in writing, and stand behind the work for 90 days with no fine print.
This page is for ES Windows owners in Stuart with a shaped window that’s fogged, binding, leaking, or simply never sat right in the opening. If that’s you, call (754) 324-4646 and a live person will answer, any hour, any day.
How ES Windows Products Fail - and How We Fix Them
ES Windows builds a solid aluminum and thermal-break product, but shaped and oversized units live a harder life in coastal Florida than a standard rectangle. Here’s what we see in Stuart homes, series by series:
- ES Impact Series radius units: stress cracks at the curve apex. Arched impact glass carries more tension at the highest point of the arc than anywhere else. When the original install left the rough opening even slightly out of true, that apex becomes the first place hairline cracks appear. We see it most often on east-facing elevations in Stuart where morning sun hits the same geometric unit for six hours a day. The fix is a recut radius panel, plus truing the opening before the new glass goes in.
- ES Essence Series trapezoids and angled transoms: seal failure at acute corners. Any window with a corner sharper than 45 degrees stresses the edge seal more than a standard 90-degree corner. ES Essence units that sit above fixed glass on Stuart Intracoastal homes tend to fog at the points first, usually within eight to twelve years. The only lasting fix is IGU replacement with fresh desiccant and a seal designed for acute geometry, not a standard rectangular spacer cut down.
- ES Elite Series oversized openings: sagging sash on wide geometric units. When an ES Elite picture window spans more than eight feet with a shaped transom above it, the weight of the upper unit slowly bears down on the lower frame if the header was undersized. We’ve pulled ES Elite units in Stuart where the lower sash had dropped a quarter inch in three years. We reinforce the opening, reset the frame, and the window stops binding.
- Roller and hinge wear on ES custom casements with radius tops. Shaped casement windows place uneven load on hinges because the sash is heavier at the top of the arc. ES Windows uses a good-quality hinge, but coastal salt air accelerates wear. When the sash begins to scrape the frame at the top corner, it’s almost always hinge pins plus a stretched arm, not the frame itself. New hardware brings it back to factory operation.
- Weep and drainage failures on curved-bottom ES units. Radius-bottom windows have a natural spot for water to pool if the weep channels were not set with the correct slope during fabrication or install. In Stuart’s summer downpours, that pooling becomes a slow leak into the sill and, eventually, the wall. We correct the slope, clear or recut the weeps, and reseal the pan before it gets to the drywall.
Our ES Windows Custom & Geometric Windows Process
We measure every opening twice. If the opening is right, the rest is just doing the work. Here’s how a typical ES Windows custom or geometric job runs with us:
- 1
The call. You reach a live person at (754) 324-4646. We ask what the window is doing, where it sits, and whether it’s a shaped or oversized unit. That tells us which technician to send.
- 2
The diagnostic visit. A background-checked, uniformed tech arrives, inspects the unit, the opening, and the installation as a whole. For geometric windows, half the problem is usually the rough opening, not the glass.
- 3
The parts decision. We quote OEM ES Windows parts when the warranty is active and aftermarket only when the OEM part is obsolete, discontinued, or the homeowner wants a cost alternative. You see both options side by side on paper before anything is ordered.
- 4
The work. Custom glass is fabricated to the exact radius or angle, then installed by someone who sets shaped units regularly, not by whoever happens to be available. We true the opening, set the panel, and seal it the way it should have been sealed the first time.
- 5
The test and the paperwork. We operate the unit through its full range, check seals and drainage, and register both warranty layers in writing before the truck leaves your driveway. Then we walk it with you.
- 6
The promise. If anything isn’t right within 90 days, we make it right. No paperwork fights, no arguing.
What ES Windows Custom & Geometric Windows Costs in Stuart
Honest numbers, based on what we’ve quoted across Martin County:
- Radius or arch IGU replacement (fogged seal, shaped unit): $600 - $1,400 depending on size, glass type, and finish
- Trapezoid or angled transom glass replacement: $500 - $1,100
- Full geometric unit replacement (frame and glass, oversized opening): $1,800 - $4,500
- Hardware rebuild on radius casement (hinges, rollers, arms): $250 - $650 per sash
- Weep and drainage correction on curved-bottom unit: $180 - $400
What moves the price: the complexity of the radius, whether the glass is impact-rated, whether the frame must be reset, and whether the original opening needs structural correction. We don’t pad quotes with surprise line items. The estimate you get on paper is the price you pay. Call (754) 324-4646 and we’ll come measure it.
Why Stuart Homeowners Call TruePane Windows & Doors for ES Windows Work
We’ve been serving Stuart and the surrounding communities since 2008 through a heritage that started with Dale Kessler’s father handing him a glass cutter at fourteen. Dale grew up in Rio, just south of Stuart along the St. Lucie River, and he’s been reading rough openings correctly on the Treasure Coast for the better part of two decades. We’re an independent ES Windows service provider, which means we work for you, not for a manufacturer’s warranty department.
Every job carries the Done Right Promise and The Keystone Standard: both warranty layers registered in writing, durations stated, before we leave. We’re also authorized installers for more than a dozen other lines including PGT, CGI, CWS, and ECO Window Systems, so if an ES Windows unit is beyond sensible repair, we quote you real alternatives side by side rather than pushing one brand. Senior and veteran discounts are permanent: 5 percent off, every job.
FAQs
If the unit is still under ES Windows warranty, we use OEM parts and follow warranty-safe procedures so the remaining coverage stays intact. We register both warranty layers in writing and document the work. Call (754) 324-4646 and we’ll check your coverage before touching anything.
Yes. We template the existing opening and glass directly, so the replacement matches the arc, angle, tint, and Low-E coating of the original. We’ve matched ES Windows units that other shops wouldn’t touch because the radius was non-standard. Bring us a photo and measurements, or we’ll come to you.
If the frame is sound and the opening is true, replacing the IGU is almost always the better financial call, usually $600 to $1,400 versus $1,800 to $4,500 for a full replacement. If the frame has sagged or the opening was never right, replacement may be the only honest option. We’ll tell you which it is and show you the math on both.
Simple glass replacement with an in-stock radius typically runs one to two visits over about a week. Fully custom fabrication with non-standard geometry usually takes two to three weeks from template to install. We’ll give you a written timeline when we quote, and we’ll be there when we say.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Stuart and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.