Mr-Glass Door Installation Nationwide | TruePane Windows & Doors

Mr-Glass Door Installation in Stuart: What to Know First

We install Mr-Glass doors in Stuart as an independent Mr-Glass service provider, and most entry or French door jobs take us one to two days from measurement to final walkthrough. The honest price posture is this: you will pay a fair mid-market rate for a door that is set square, sealed correctly, and backed in writing, not a bargain rate that gets revisited with a change order after the old door comes out. If you own a Mr-Glass door that needs setting, replacing, or re-hanging, this page is written for you.

Call (754) 324-4646

Call (754) 324-4646 and a live person answers. We do not run a voicemail tree.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass doors show up in plenty of Stuart homes, and after decades working with them across Martin County, we know exactly where they tend to fail. Here is what we see and what we do about it.

• Threshold rot on the Classic Series entry doors. The original wood threshold on older Classic Series doors traps moisture against the door sweep, and in Stuart’s humidity that means rot within ten to twelve years. We replace the threshold with a composite unit, re-shim the rough opening, and reset the door so the sweep lands clean. The fix holds because the new threshold does not wick water.
• Sagging French door panels on the hinged Signature Series. The top hinge mortises on these heavier doors were cut shallow at the factory, and after years of coastal humidity cycling, the screws lose bite and the active panel drags. We bore the mortises deeper, set longer screws into the framing, and re-align the astragal. The panel that could not close in August closes with two fingers.
• Fogged glass on Mr-Glass patio door units. The sealed glass units on early-2000s Mr-Glass sliders lose their argon fill faster in Stuart’s salt air than the manufacturer’s original rating suggested. When the glass fogs between the panes, the seal is gone and the unit must be replaced. We measure the sash, order a matched insulated unit, and install it without replacing the entire door frame.
• Weatherstripping wear on the sliding door tracks. The original vinyl weatherstripping on Mr-Glass sliders hardens and breaks down under UV exposure within five to seven years in Florida sun. Owners notice drafts and bugs and assume they need a new door. Most of the time, the frame is fine and the door only needs new weatherstripping and a track cleaning. We do that first and only recommend replacement when the frame itself is compromised.
• Improper rough openings from the original install. This is the one we see most often when another contractor set the door. A Mr-Glass door installed into an out-of-square opening binds at the top corner or leaks at the sill within a year. We strip the casing, measure the opening, and correct whatever was done wrong before the new door goes in. If the opening is right, the rest is just doing the work.

Our Mr-Glass Door Installation Process

Every Mr-Glass job follows the same sequence, whether it is a replacement entry door or a full French door install. Dale Kessler grew up in Rio and learned to read a rough opening correctly the first time, and that habit runs through everything we do.

1. 1
   Call and schedule. A live person answers, asks a few questions about the door, and schedules a measurement visit. No form, no callback, no waiting.
2. 2
   Measure the opening twice. We measure the rough opening, the jamb depth, the reveal, and the floor height at three points. If the floor is not level, we note it before the quote, not after the old door is out.
3. 3
   Quote on paper, side by side. We show you OEM Mr-Glass parts alongside quality aftermarket options, with prices, so you see exactly what you are buying. No surprise line items on the bill.
4. 4
   Set the door square and plumb. We shim every hinge and strike point, seal the sill with a proper pan, and sit the door so it swings true in both directions. If the pane is not true, the job is not done.
5. 5
   Test for gaps, drafts, and drag. We run a dollar-bill test on the weatherstripping, check the sweep against the threshold, and open and close the door a dozen times. If it binds in the July heat, we fix it before we leave.
6. 6
   Register both warranty layers and walk you through. Before the truck leaves the driveway, your manufacturer warranty is registered in writing with the duration stated, and our Done Right Promise is on paper. If it is not done right, we make it right. No paperwork fights.

What Mr-Glass Door Installation Costs in Stuart

Here are the ranges we have seen on Mr-Glass door work in Stuart over the last several years. Every job is quoted on paper, so these are ballparks, not bids.

• Weatherstripping replacement and track service: $75-$200 per door
• Threshold replacement with composite unit: $300-$650 installed
• French door re-hang and alignment: $400-$900 depending on framing repairs needed
• Full entry door replacement with mid-grade Mr-Glass door: $1,800-$3,800 installed
• Patio slider glass unit replacement (fogged seal): $450-$1,200 per sash

What moves the price is the condition of the rough opening, whether framing repair is needed, and whether you choose OEM or quality aftermarket parts. Call (754) 324-4646 for an exact quote. Estimates are free, and the number you get is the number you pay.

Why Stuart Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We have been setting doors on the Treasure Coast since 2008, and Dale Kessler founded TruePane in 2008 on the principle that out-of-true installs and voided warranties were problems worth fixing permanently. We are background-checked, uniformed technicians who measure every opening twice and register both warranty layers before the truck leaves the driveway. The Keystone Standard means your manufacturer warranty is in writing with the duration stated, and our Done Right Promise means if it is not right, we make it right, no arguing. If you are weighing a Mr-Glass door against something else, we are also an authorized installer for PGT, CGI, CWS, and ES Windows, so we can show you side by side what each line costs and why. A square deal, in writing.

FAQs