Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Roof Repair in Stuart: What to Know First
Therma-Tru products in Stuart homes are mostly entry and patio door systems, not roofing systems, so when a Stuart homeowner calls us about “Therma-Tru roof repair,” the real problem is almost always water getting past the door header, transom, or sidelight framing and into the roof deck or ceiling below. We provide independent Therma-Tru door and frame repair in Stuart, typically completing the job in one visit with OEM-grade weatherseal, flashing, and sill components. Estimates are free, and our pricing is stated up front before any work begins.
This page is written for Stuart homeowners who own a Therma-Tru door system and are seeing water stains, peeling paint, or soft drywall near the door header. If that sounds familiar, call (754) 324-4646 and talk to a live person.
How Therma-Tru Products Fail - and How We Fix Them
- Header flashing separation on Therma-Tru Classic-Craft and Smooth-Star entry systems. The door unit ships with an integrated nailing fin and drip cap, but Stuart’s summer downpours and salt air work on the sealant joint where the fin meets the housewrap. When that bond fails, water rides the fin behind the siding and settles into the header. We see this on doors installed before 2010 most often. Our fix is to remove the failed sealant, reset the flashing with stainless fasteners, and install a new drip cap with a proper 1/4-inch overhang. Done right, it routes water away instead of into the wall cavity.
- Transom and sidelight frame deflection on Therma-Tru 8-foot entry systems. Taller units carry more wind load, and Stuart sees sustained 20 to 30 mph gusts through hurricane season. Over time the milled jambs can deflect just enough to break the corner seal at the transom junction. Homeowners notice a hairline gap that leaks during driving rain. We correct this by re-shimming the rough opening to manufacturer spec, replacing the corner gasket, and re-caulking with a marine-grade sealant rated for coastal Florida.
- Compressed or torn Q-Lon weatherstrip on Therma-Tru fiberglass doors. The Q-Lon seal is good material, but it has a service life. After eight to ten years in Stuart humidity, the compression set leaves gaps at the top corners. Rain driven against the door face gets pulled in by the pressure difference. The symptom is a wet floor after storms, but the long-term problem is moisture wicking into the subfloor. We replace Q-Lon weatherstrip with the correct durometer material and adjust the strike plate so the door compresses the seal evenly.
- Failed corner sealant on Therma-Tru patio door headers. Multi-panel Therma-Tru patio systems have factory-applied sealant at the header corners. On southwestern Stuart exposures, UV breaks that sealant down faster than the rest of the frame. You’ll see chalky, cracked sealant and, after heavy rain, water in the track. We strip the old sealant completely, clean the joint, and apply a UV-stable polyether sealant that holds up under direct sun better than what shipped from the factory.
- Improper sill pan installation from the original build. This is the one Dale Kessler talks about most. A Therma-Tru door installed directly on the subfloor without a sill pan will eventually leak at the threshold, because Stuart concrete slabs wick moisture upward. The fix means pulling the door, installing a proper sill pan with end dams, and resetting the unit. It’s invasive, but it’s the difference between fixing the leak and chasing it for years.
Our Therma-Tru Roof Repair Process
Every Therma-Tru repair we do in Stuart follows the same sequence. No shortcuts, no second visit left hanging.
- 1
Call and talk to a person. You reach a live dispatcher at (754) 324-4646, describe what you’re seeing, and we schedule a window that works for you. We show up when we say we will.
- 2
On-site diagnosis of the rough opening. We inspect the door, the header, the flashing, and the surrounding wall cavity. Dale’s rule applies: if the opening is right, the rest is just doing the work. We measure twice before we touch anything.
- 3
Parts decision on paper. We quote OEM Therma-Tru components and quality aftermarket equivalents side by side, with prices written down. You decide. If the OEM part carries a longer functional life, we tell you why.
- 4
The repair. We remove failed materials, correct any underlying framing or flashing issue, install the new components, and seal everything with materials rated for Stuart’s coastal climate.
- 5
Water test and inspection. We run water over the repair area and watch. If it leaks, we’re not done. When it holds, we walk you through what we did.
- 6
Warranty registered in writing. Both warranty layers on any new component are registered before the truck leaves the driveway. The Done Right Promise covers our workmanship, in writing.
What Therma-Tru Roof Repair Costs in Stuart
Most Therma-Tru door and header repairs in Stuart run between $225 and $650 depending on what failed and how much has to be removed to fix it properly. Here’s what we typically see:
- Weatherstrip replacement (single door, Q-Lon or equivalent): $85 to $180
- Drip cap and header flashing reset: $200 to $400
- Transom or sidelight corner reseal: $150 to $350
- Threshold rebuild with sill pan installation: $450 to $900
- Full door pull, reflash, and reset: $600 to $1,200
What moves the price is access, the condition of the surrounding framing, and whether the original installer left us problems to undo. We don’t change the number once we start. Your estimate is your price. Call (754) 324-4646 for a free estimate on your Therma-Tru repair.
Why Stuart Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We’ve served Stuart and the Treasure Coast since 2008, founded by second-generation glazier Dale Kessler on a simple idea: out-of-true installs and voided warranties were problems worth fixing permanently. That’s the Keystone Standard. Every job gets both manufacturer warranty layers registered in writing, durations stated, before we leave. Every repair carries the Done Right Promise. If it’s not done right, we make it right. No paperwork fights, no arguing.
Our technicians are background-checked and uniformed, trained to work in your home the way they’d work in their own mother’s. And because we’re also an authorized installer for PGT, CGI, CWS, and ES Windows, we can talk honestly about your options when a repair doesn’t make sense. A live person answers our phone 24 hours a day, seven days a week. Not a recording. Not a call center.
FAQs
Therma-Tru’s written warranty covers manufacturing defects in the door slab and components, not water damage caused by installation errors or failed weatherseal after the coverage period ends. That’s why we register both warranty layers in writing on every job and why our Done Right Promise covers our workmanship separately. If your door is still under warranty with a covered defect, we’ll help you document the claim. Call (754) 324-4646 and we’ll take a look.
We quote both. On most Stuart homes we can source OEM Therma-Tru replacement weatherseal, sills, and hardware directly from Therma-Tru distribution channels, and we’ll show you the cost side by side with quality aftermarket equivalents on paper. As an independent Therma-Tru service provider, we’re not limited to one parts stream, which means we can tell you when the cheaper part is a bad idea and when it’s identical in function. You decide with the numbers in front of you.
Most Therma-Tru repairs in Stuart are scheduled within a few business days, and a live person answers our phone at (754) 324-4646 around the clock to get you on the schedule. We’re not a regional call center. When you call, you talk to someone from our shop who knows the Stuart service area. If water is actively coming in, tell the dispatcher and we’ll prioritize you.
If the frame is rotted through, the slab is warped from moisture, or the original install was so far out of true that we’d be rebuilding the opening anyway, replacement is usually the smarter money. Because we install PGT, CGI, CWS, and ES Windows alongside Therma-Tru-compatible entry systems, we can show you what a full replacement costs with impact-rated components built for Stuart’s wind zone. Either way, you get the straight answer, not an upsell.
Replacing a worn sweep or tightening a strike plate is reasonable for a handy homeowner. Anything involving the header flashing, sill pan, or transom seal is not, because if you get it wrong, the water keeps coming and the rot spreads behind the wall where you can’t see it. Water intrusion near a door header can also put hidden moisture against electrical wiring. That’s a job for someone who reads rough openings for a living. Call (754) 324-4646 and we’ll diagnose it properly.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Stuart and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.