Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterAndersen Windows & Doors in Jensen Beach, FL | TruePane Windows & Doors
If you own Andersen windows or doors in Jensen Beach, you already know the brand is worth maintaining. We’re an independent Andersen service provider, not a manufacturer affiliate, and we repair, adjust, and replace Andersen products across Jensen Beach every week. The factor that separates our Andersen work here is simple: we know what early-2000s post-hurricane installs look like after twenty years of salt air from two directions, and we quote repair-vs-replace honestly against that reality. Call (754) 324-4646 for a free estimate.
Why Jensen Beach Residents Choose Us for Andersen Service
Andersen builds a good product, but Jensen Beach punishes it in ways most installers never planned for. We carry OEM Andersen parts for weatherstripping, balance systems, and multi-point locks so we don’t hand homeowners aftermarket hardware that fails in two seasons. Dale Kessler, our owner, grew up in Rio and spent two decades setting and sealing windows up and down the Treasure Coast before opening TruePane. He reads a rough opening correctly the first time, and he doesn’t upsell glass a homeowner doesn’t need. If the opening is right, the rest is just doing the work.
Common Andersen Windows & Doors Problems We Solve in Jensen Beach
- Pitting and corrosion on Perma-Shield aluminum cladding. The Indian River Lagoon sits a mile west and the Atlantic a mile east, so salt-laden air hits Jensen Beach homes from both sides. Andersen 200 Series Perma-Shield cladding eventually pits and lifts, and once water gets behind it, the frame starts going. We remove the damaged cladding and replace it before rot spreads to the wood core.
- Fogged glass on mid-2000s 400 Series casements. The wave of Andersen installs that followed Hurricanes Frances and Jeanne in 2004 are now nearly twenty years old. Failed IG seals on 400 Series casement and picture windows show up as fogging between the panes, and Jensen Beach’s humidity makes it worse. We replace the insulated glass unit where the frame is still sound, and we tell you plainly when the frame isn’t.
- Sagging Frenchwood hinged doors. A Frenchwood patio door that’s been through twenty years of humidity cycles will start to bind in July. Wood panel movement is normal. What isn’t normal is a door that won’t close without a shoulder. We reset hinges, plane where needed, and adjust the threshold so the door operates like it should.
- Seized multi-point lock hardware. Sand and salt intrusion grind down the gearbox inside Andersen E-Series and 400 Series multi-point locks. If the handle turns but the door won’t deadbolt, the mechanism is usually packed with corrosion. We rebuild with OEM Andersen hardware rather than telling a homeowner to live with a door that only catches at one point.
- Air leaks around old Narroline sliders. Pre-2004 Narroline single-pane sliders in 1960s and 1970s Jensen Beach homes are drafty by design. Short of full replacement, new OEM weatherstripping and roller replacement closes the worst of the gap while the homeowner decides whether impact glass is next.
Andersen Service in Jensen Beach: What Local Conditions Mean for Your Equipment
Jensen Beach absorbed near-direct hits from Hurricanes Frances and Jeanne within 26 days in 2004, and the post-storm rebuild pushed a huge number of Andersen impact windows and doors into local homes. Those units are now hitting the twenty-year mark, and the town has one of the highest concentrations of early-2000s Andersen Perma-Shield installs on the Treasure Coast. The cladding is pitting from two decades of lagoon and Atlantic salt, seals are failing on 400 Series casements along NE Savannah Road and the canal-front streets off Jensen Beach Boulevard, and multi-point locks are seizing on Frenchwood doors that haven’t been serviced since they were hung. Here’s what most national advice misses: in Martin County, any permitted window or door work must meet wind-borne debris requirements under the Florida Building Code. A simple glass swap on a pre-2004 Andersen frame can trigger a four-point inspection, and if the frame doesn’t document as impact-rated, the homeowner can lose coverage with Citizens. We routinely coordinate with local inspectors to document impact-rated upgrades so Jensen Beach homeowners stay insurable without paying for a full replacement they don’t need.
Andersen Models & Products We Service in Jensen Beach
We work on the Andersen lines most common in Jensen Beach: 400 Series Frenchwood hinged and gliding doors, 200 Series Perma-Shield windows and doors, E-Series hinged door systems, and the older Narroline sliders still sitting in original 1960s and 1970s concrete block homes. For critical components including weatherstripping, balance systems, and multi-point lock gearboxes, we use OEM Andersen parts. For cladding and trim where the manufacturer part is priced against the cost of a full sash, we’ll offer a quality aftermarket alternative and show you both numbers on paper. Our rule is honest: when a failed IG unit sits in a frame with extensive corrosion, or repair costs approach 60 percent of replacement on a pre-2004 install that doesn’t meet current wind-load code, we’ll tell you replacement is the better money. No upsell, no drama.
Andersen Service Pricing in Jensen Beach
Andersen service in Jensen Beach typically runs $180 to $550 for component repairs like weatherstripping, hinge resets, and multi-point lock rebuilds. Insulated glass unit replacement on a 400 Series casement falls between $350 and $900 depending on glass package and size. Full frame replacement of a Frenchwood patio door with impact-rated Andersen product starts around $2,800 and goes up with custom sizing and finish. What drives the bill here is salt exposure, not labor rates: a door that needs its cladding stripped and the wood core checked takes longer than a clean inland job. Every estimate is free, written, and line-itemed. Call (754) 324-4646 for exact numbers.
Serving Jensen Beach, FL - Our Local Coverage Area
We’re based in the Jensen Beach area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Andersen Windows & Doors in Jensen Beach
Yes, in most cases the insulated glass unit can be replaced without pulling the whole frame, provided the Perma-Shield cladding and wood core are still sound. On a 2005 install in Jensen Beach, we’ll inspect for the salt-driven frame corrosion that’s common here before we quote glass-only work. Call (754) 324-4646 for an exact quote, and we’ll put it in writing.
We do. Humidity-driven panel movement on Frenchwood hinged doors is a standard repair for us in Jensen Beach, and the fix is usually hinge reset or replacement with OEM Andersen hardware rather than a full door swap. The condition of the frame dictates which one applies.
In most pre-2004 Narroline frames, no. The frames were not built for the glass thickness and structural load that impact-rated units require. We’ll measure the opening, show you the frame condition in person, and quote a full frame replacement that meets current Martin County wind-load code.
It depends on the frame. A four-point inspection is checking for impact-rated or protected openings, not just functioning hardware. If your Andersen windows or doors are impact-rated and documented, repair keeps them current. If they predate the 2004 hurricanes and lack impact glazing, repair won’t satisfy the inspection, and we’ll tell you that before you spend the money. Call (754) 324-4646 to have us look.
For Jensen Beach’s salt air and wind-load reality, the Andersen 400 Series with impact-rated glass is typically what we quote, either as an insert or full frame replacement depending on the condition of the original buck and the block opening. We’ll put Andersen and at least one other manufacturer line side by side on paper so you see the difference in writing.
Service Areas Near Jensen Beach
We serve Jensen Beach and the surrounding Treasure Coast communities, including Stuart, Palm City, Hobe Sound, Port Salerno, and Sewall’s Point. If you’re nearby and own Andersen products, you can visit our Andersen sales & service page or our Jensen Beach service area page for details. We also cover Andersen service in Stuart and Andersen service in Hobe Sound.
Book Your Andersen Service in Jensen Beach Today
Call (754) 324-4646 to schedule your free Andersen service estimate in Jensen Beach. A live person answers, we’ll be there when we say, and the quote is in writing before any work begins.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Jensen Beach since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.